Soft Tissue Starter Pack (Form 3)

SKU: PKG-ST-FMYW

$285excl. sales tax

Soft Tissue Starter Pack (Form 3)

Bulk Order Discount

15%
30 L
20%
60 L
25%
120 L
30%
240 L
35%
1,000 L
40%
2,000 L
45%
3,000 L

Accessories

  • $149Form 3 Resin Tank V2.1

    Form 3 Resin Tank V2.1

    Low Force Stereolithography (LFS)™ 3D printing uses linear illumination and a flexible film tank to turn liquid resin into flawless parts. A key component of the LFS process, the strong dual-layer film at the bottom of the Form 3 Resin Tank, allows for a dynamic and precise print process.

    Notice: Form 3 Resin Tank V2.1 is compatible with all Formlabs resins, but is required for use with some specific materials. There are two previous versions of the Form 3 Resin Tank, Tank V1 and Tank V2, each with their own compatibility requirements. Read more about all tank versions, compatibility, lifetime, and maintenance in our support article.

    Form 3 Resin Tank V2.1

    Tech specs

    Compatible Printer
    Form 3B
    $149
  • $299Form 3L Resin Tank V3

    Form 3L Resin Tank V3

    Low Force Stereolithography (LFS)™ 3D printing uses linear illumination and a flexible film tank to turn liquid resin into flawless parts. A key component of the LFS process, the strong dual-layer film at the bottom of the Form 3L Resin Tank allows for a dynamic and precise print process, scaled up for large format printing.

    Form 3L Resin Tank V3 offers an improved print success rate in some cases compared to the previous version of the Form 3L Resin Tank V2.

    Form 3L Resin Tank V3
    $299
Soft Tissue Starter Pack (Form 3)$285
Soft Tissue Starter Pack (Form 3)$285

Ready to orderSoft Tissue Starter Pack (Form 3)

$285excl. sales tax

Applications

Soft Tissue Starter Pack empowers dental laboratories to print gingiva masks for implant models and other soft tissue models on a Formlabs printer.

 

Soft tissue with dental models

Minimize chairside adjustment time

Soft tissue with dental models

Consistently check implant prosthetics

Material Properties*

Soft Tissue Starter Pack (Flexible 80A Resin)

Download Soft Tissue Technical Data Sheet

Download Soft Tissue Safety Data Sheet

Parameter Value

Ultimate Tensile Strength

8.9 MPa

Elongation

120%

Compression Set (23 °C for 22 hours)

3%

Shore Hardness

80A

Bayshore Resilience

28%

* Material properties may vary based on part geometry, print orientation, print settings, and temperature. Data was obtained from parts printed using Form 3, 100 μm, Flexible 80A settings, washed in Form Wash for 10 minutes and post-cured with Form Cure at 60 °C for 10 minutes.

Workflow

3D Printing Soft Tissue for Gingiva Mask on Dental Models

Washing

The foundational step in any SLA post-processing workflow is to remove any excess resin on the surface of the parts through an alcohol or ether wash.

SETTINGS

Form Wash | Form Wash L

Curing

Follow the recommended curing settings for the resin.

SETTINGS

Form Cure V1 | Form Cure V2 | Form Cure L V1 | Form Cure L V2

FAQ

The Soft Tissue Starter Pack enables dental laboratories to create custom-colored, flexible gingiva masks for use in combination with rigid dental models. These soft tissue components let you confidently check implant prosthetics by adding removable soft tissue to your model production, helping to minimize chairside adjustment time and consistently verify implant prosthetics.

No. The Soft Tissue Starter Pack is intended strictly for extra-oral use on dental models. It must not be used inside a patient's mouth.

Formlabs provides a dedicated application guide covering the complete digital workflow, mixing instructions, and best practices. You can access it at the implant models guide on Formlabs Dental.

The pack includes a Flexible 80A Resin base along with three color pigments: Magenta, Yellow, and White. These pigments are mixed into the resin base to achieve your desired gingiva shade.

By mixing the included pigments into the Flexible 80A Resin base, you can produce dark, medium, and light pink shades to match a variety of patient tissue tones.

Yes. The Magenta Color Pigment, Yellow Color Pigment, and White Color Pigment are each available for individual purchase.

The Soft Tissue Starter Pack (Form 3) is compatible with the Form 3B, Form 3BL, and Form 2 printers.

Compatible tanks include the Form 2 LT Tank and the Form 3 Resin Tank V2.1. Compatible build platforms include the Form 3 Build Platform, Form 3 Build Platform 2, Form 3 Stainless Steel Build Platform, Form 3L Build Platform, and Form 3L Build Platform 2L.

When printed at 100 μm using Flexible 80A settings, the cured material offers an ultimate tensile strength of 8.9 MPa, 120% elongation, a Shore Hardness of 80A, a compression set of 3% at 23 °C for 22 hours, and a Bayshore Resilience of 28%. Note that properties may vary based on part geometry, print orientation, print settings, and temperature. You can download the full Soft Tissue Technical Data Sheet for complete details.

Reference data for this material was obtained from parts washed in Form Wash for 10 minutes and post-cured in Form Cure at 60 °C for 10 minutes. Following these steps helps ensure consistent material properties in your finished gingiva masks.